Last updated: 23 October 2026
Camstead is a viewer for IP security cameras you already own. It can also turn a spare iPhone or iPad into a camera. It connects directly to cameras on your own network using standard protocols — RTSP, ONVIF and MJPEG — so video travels only between your own devices and cameras, and snapshots and recordings stay on your device. There is no Camstead account and no Camstead cloud.
rtsp:// address, or an http:// address for MJPEG).No camera to hand? Turn on Settings → Demo cameras to try the app with simulated feeds.
An old iPhone or iPad can become a camera that Camstead on your main iPhone or iPad watches over your home Wi-Fi. You need Camstead installed on both devices, and video goes straight between them, with no account and no cloud.
If the QR code cannot be scanned, use the same Nearby device screen instead: type the address and PIN shown on the spare device under Enter address manually.
Devices on the same Wi-Fi network also appear in the list on that screen under On this network. Tap the one you want and type the PIN shown on it.
A spare-device camera works on your home network. To watch it from outside your home network, the two devices need to be on the same VPN (for example Tailscale). You then add the camera using its VPN address. Camstead has no relay of its own. If you prefer, you can run a relay yourself and switch on Use a relay under Remote access in the camera's settings; it carries your video, so host it somewhere you trust.
Any camera that exposes RTSP, ONVIF or MJPEG on your local network. That covers most models from Reolink, Hikvision, Dahua, Amcrest, Axis, Foscam, TP-Link Tapo, Hanwha, Vivotek, D-Link, Ubiquiti, Wansview, VStarcam, Yi (with RTSP firmware), Swann and many others, plus NVRs that re-publish their channels.
Cameras that offer no local stream at all and only talk to their maker's cloud over a proprietary protocol. Battery- and LTE-powered models often fall into this group, because they stay asleep to save power and cannot serve a continuous stream. If your camera has no RTSP or ONVIF option in its own app's settings, it will not work with any third-party viewer.
Automatic discovery uses network multicast, which some routers and most guest or VPN networks block. Adding the camera by IP address always works. Check that RTSP or ONVIF is enabled in the camera's own settings, and that you are on the main Wi-Fi network rather than a guest network.
If the camera is a spare iPhone or iPad running Camstead, you can scan the QR code shown on it, or type its address and PIN under Enter address manually on the Nearby device screen (+ → Add camera → Another device). Neither needs automatic discovery. The steps are in the section above on using a spare iPhone or iPad as a camera.
Switch that camera to the Fluent stream, or reduce the grid to fewer columns. Each extra tile is another live decode. Wi-Fi signal at the camera end is the most common cause.
Audio must be enabled on the camera, and the stream must carry it. Tap Listen in the full-screen view. Two-way Talk needs a camera with an ONVIF audio backchannel and must be switched on for that camera in its settings.
If the camera is a spare iPhone or iPad, check that Send audio is on in its camera settings and that Microphone access is allowed. The live view shows Audio paused (or No audio) while the microphone is not running, for example after a call, Siri or a headset has taken it.
On your device. Open a camera full-screen and tap Clips. From there you can play, share or delete a recording. Recordings contain video only, no sound. Snapshots you take with Snap are saved in the Events tab. Camstead uploads nothing.
If a spare iPhone or iPad is saving motion clips (Motion and Auto-record in its camera settings), those clips stay on that device, not on the one you watch with. Open its camera settings and tap Clips to play, share or delete them. The Events tab on your main device only shows that a clip was recorded.
No. Camstead does not send notifications or alerts of any kind. Detected motion is listed in the Events tab, and the app checks for motion only while a camera is showing on screen. A spare iPhone or iPad with Motion switched on checks its own picture whenever its camera screen is open, even with no viewer connected. The device you watch with collects those events only while that camera is on screen, and adds the recent ones the next time you open it.
Open Settings → Camstead Pro and tap Restore Purchases. Make sure you are signed in to the same Apple Account that made the original purchase. Subscriptions are managed in your Apple Account settings, not in the app.
Camstead keeps everything on your own devices. To remove a camera and its saved password, open Settings, tap the camera and choose Remove camera. Its recordings and events are not deleted with it, and its clips can no longer be opened, so delete those first. To remove a vendor cloud account (Wyze, Tuya, Ring, Nest, Blink or Eufy), open Settings, then Vendor cloud accounts, and choose Sign out: that deletes its saved sign-in from the device and removes the cameras you added through it since version 1.2.1. Deleting the app removes the files it stored, but iOS may keep Keychain items such as camera passwords and vendor sign-in tokens after an app is deleted, so remove your cameras and sign out of your vendor cloud accounts first. See the Privacy Policy for detail.
Camstead is a viewer, not a monitoring service. It is not a life-safety or alarm-monitoring system and must not be relied on as one. It does not send notifications or alerts.
Mobile Alchemy LTD